- Description
-
Details
Pulse & direction stepper motor driver, RS232 serial stepper motor controller, two function in one Stepper Controller.
Set working current:
Set Micro-step:
● Miniature size 42.3mmx42.3mm x21mm
● Pulse & direction stepper driver also support the standard RS232 serial command, and built-in 32bit digital chip.
● Using new control algorithms such for vibration suppression and low heat generation
● DC input voltage 12~32VDC, recommended working voltage 24VDC.
● Continuous output current 1.58A max, max peak current 2.2A.
● Integrated design, mounted with 42/39mm stepper motor.
● Low vibration, low noise, stable operation, low motor heating.
● Any microstep can be set .
● Protection functions such as overvoltage, undervoltage and overcurrent.
● Built-in automatic matching function of motor parameter.
● ADM42 stepper driver can be assembled for NEMA17 Integrated Stepper Motors
1.VDC: Positive power input: DC voltage 12-32VDC
2.GND: Negative power input: DC voltage GND
3.OPTO: Pules Direction,Enable common anode Input: 5V DC,
4.PUL-: Pulse Control Signal Input, Rising Edge effective
5.DIR-: Direction Control Signal Input, Rising Edge effective
6.ENA-: Enable Signal Input, Rising Edge effective
7.TXD: To the TX pin on user device
8.RXD: To the RX pin on user device
Wiring:
ADM57 Pulse & direction stepper driver, RS232 serial Stepper Motor Controller
RS232 Serial Stepper Motor Controller, Pulse and direction stepper driver,
ADM57 is design for NEMA23 Integrated Stepper Motors.
ADM57 Miniature integrated stepper motor driver
1. With same size as NEMA23 stepper motor,
2. Built-in 32-bit DSP digital chip.
3. Using new control algorithms such for vibration suppression and low heat-generation
4. Ensure the motor runs smoothly, with low noise and temperature controllable.
5. ADM57 Stepper Driver with Max.Output current: 5.6A, meet the all of NEMA23 stepper motor application requirement.
6. Achieve High subdivision effects through internal algorithms, even in the low micro-step condition, which widely applied in laser wire solutions.
7. Integrated automatic matching function for motor parameters, Optimize the operating parameters, make sure the motors in good performance.
8. ADM57 stepper controller can be assembled as NEMA23 Integrated Stepper MotorsPin No.
Name
Description
1
+VDC
Supply voltage: 12-50VDC
2
GND
Supply Voltage Ground: GND/0V
3
PUL+
Pulse Control Signal Input: Rising Edge effective,
PUL high level: 4~5V,, Low level : 0~5V .
Make sure pulse signal effective, pulse width≥1.2μs,
Add the resistance for power supply.
4
PUL-
5
DIR+
Direction Signal: high/low level signal:pulse width>5μs ,
High level: 4~5V,Low level: 0~0.5V
6
DIR-
7
ENA+
Enable sigla:enable/disable.
If ENA+ connect +5V, ENA- connect low level(or Internal optocoupler on), stepper controller will turn off the current, motor in free state, no feedback even send pulses.
8
ENA-
9
TXD
To the TX pin on user device
10
RXD
To the RX pin on user device
ADM57 stepper motor driver, using 6 DIP switch for set the current and Micro-step:
Set working current:
Output Peak current
Mean current
S1
S2
S3
Default 1.5A
1.1A
ON
ON
ON
2.1A
1.5A
OFF
ON
ON
2.7A
1.9A
ON
OFF
ON
3.2A
2.3A
OFF
OFF
ON
3.8A
2.7A
ON
ON
OFF
4.3A
3.1A
OFF
ON
OFF
4.9A
3.5A
ON
OFF
OFF
5.6A
4.0A
OFF
OFF
OFF
Set Micro step.
Pulses/revolution (Micro-step)
S4
S5
S6
Default 400(1/2 Micro-Step)
ON
ON
ON
800 (1/4 Micro-Step)
OFF
ON
ON
1600 (1/8 Micro-Step)
ON
OFF
ON
3200 (1/16 Micro-Step)
OFF
OFF
ON
4000 (1/20 Micro-Step)
ON
ON
OFF
5000 (1/25 Micro-Step)
OFF
ON
OFF
6400 (1/32 Micro-Step)
ON
OFF
OFF
12800 (1/64 Micro-Step)
OFF
OFF
OFF
Input signal Single ended cathode connection:
Input signal Single ended common anode connection:
Input signal Single ended cathode connection:
- Additional Information
-
Additional Information
Image Gallery N/A - Reviews
-